Jump to content
Cookie

In Search of the Holy Grail - Super Clean Smoke

Recommended Posts

Here I am on a Friday night waiting for guests to arrive. Cold beverage in hand and I've been playing with the dampers on my new 21". I'm using KK extruded for heat and peach wood for smoke (ribs). Temp floating around 240F.

When I added two good size peach chunks, I got the billowy white smoke we don't want. Then I started playing with the dampers. The beauty of this new dual damper is you can go with a really small opening on the bottom. This allowed me to open up the top a full two turns and I'm still hovering around at 240. When I did this, the smoke really started streaming and went from white to light, but still looked a little dirty. Now I'm barely seeing any smoke and wondering if im really running that clean holy grail smoke, or if my chunks have burned up altogether.

I'm not willing to open the lid as I'm on a timeline, but look forward to checking the basket when finished to see if my peach chunks are still burning. Will report back.

post-522-0-63377500-1435316771_thumb.jpg

  • Like 1
Link to comment
Share on other sites

You've seen a manual with the new dual damper or you mean the one for the single bottom damper? Can you send me a pic? With the single bottom damper, even a small crack open is a small crack open in 3 places and a lot more than what you can do with the new one. Please share if you have a diagram for the new one?

Link to comment
Share on other sites

You've seen a manual with the new dual damper or you mean the one for the single bottom damper? Can you send me a pic? With the single bottom damper, even a small crack open is a small crack open in 3 places and a lot more than what you can do with the new one. Please share if you have a diagram for the new one?

You're correct, I haven't seen a diagram on the dual set up, but I think the principal is the same. I believe that as long as you can maintain your desired temp, closed bottom, open top, less smoke.

Robert

Link to comment
Share on other sites

My stove top smoker uses 1-2 T wood chips just larger than saw dust. Smoke taste is great. Just a thought.

It uses no where near the amount of wood we do.

Wood is just put on metal that sits on the heat source. In a short time it puts out the smoke that more than flavors product. Wood is about size of normal medicine capsule. I think smoke is a product surface thing.

Works for me. You might consider playing in this area.

Link to comment
Share on other sites

Agree, but figuring out the balance is going to take some time....I have a feeling I burned my chunks up in a hurry, but was trying to get to blue.

I bet you didn't. I can't remember a time that my chunks burned completely in my kk. I use roughly 2-4 3" chunks, and I put them on the hot spot in the coals about 30 minutes before I plan to add my protiens. The air flow is so low that it doesn't allow a conventional fire with flames and the wood burns similarly to the coal, a slow smolder.

Robert

  • Like 1
Link to comment
Share on other sites

^ similar experience and method here; however at least 50% of the time, and 100% for low and slow, I use my MSR lidded pot for the smoking wood chunks. Sometimes, especially for the low-slow sessions I'll use a chimney just for the smoking wood chunks to more quickly get the acrid white smoke burned off, then the chunks go into the pot atop the already lit coals & heat soaked KK.

Link to comment
Share on other sites

dstr8 -  Would some type clamp top pot with holes work for this?

 

Exactly.  I got the idea from someone else on our KK forum a couple years ago...apologies to that person for me not remembering who to credit!  Drilled 3 holes in the top...then lid side goes down into the lump coals.  Seems to work very well and although the cast iron dutch oven with flour paste seal-off probably works better...the MSR pot is better for my somewhat lazy ways :D

 

This:  

 

post-1238-0-57059000-1435327714.jpg

  • Like 2
Link to comment
Share on other sites

I've got the smoke pot (dutch oven with the hole), have done it, but never get enough smoke flavor for my liking.  What I'm trying to do is replicate what an offset smoker can do...really clean / blue smoke with wood added to a small hot fire, keeping a low overall pit temp.  I added these chunks tonight to the hot spot that had been going for weover an hour and the pit temp was already at 240F.  I let them burn for about 40 minutes before throwing on the ribs, and I played with the dampers after closing the lid.  Two full turns open on top with one of the smallest holes on bottom was all I used to get a rapid stream of fairly clean smoke flowing out of the top.  However, it didn't last all that long, so it either went to the really clean stage or I torched them..won't know till tomorrow when I have a peak.  I pulled the ribs and shut it down tonight to save any left over fuel.  I actually wanted my chunks to ignite (not smolder) as my understanding is that is that is how you get the true clean / blue smoke.  If it smolders, you are going to get some of that white smoke.  The trick is to get them to ignite without burning up too quick.

 

I do like the pre-burn ideas...that could be the ticket.  Will let you all know tomorrow if there are any remnants of those peach chunks left in the basket.

Link to comment
Share on other sites

How about Practice runs now with no product in the unit? Maybe mix wood in where there is no fire to be later. Some where there is fire. Some of different sizes in both places.  Why wait?  Komono Kamado will - if you will. Wishing you well going from the known to the unknown.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



×
×
  • Create New...