CaptMorg82 Posted June 30, 2022 Report Share Posted June 30, 2022 Hi all, I only have 2 pieces that fit into the end of my rotisserie. Am I missing one? One is very pointy which I assume is used to skewer. The other is a round cylinder with a nut which slides into the left side. Should I have a piece for the right side that fits into the hole by the motor? Sent from my iPhone using Tapatalk Quote Link to comment Share on other sites More sharing options...
David Chang Posted June 30, 2022 Report Share Posted June 30, 2022 there should be a spring loaded end (missing in your pictures) that goes on the opposite side of the grill. and the adjustable screw end (your first picture) that is length adjusted to fit the motor end of the grill. the screw on spike (your second picture) is to skewer meat, and not for mounting. Quote Link to comment Share on other sites More sharing options...
CaptMorg82 Posted June 30, 2022 Author Report Share Posted June 30, 2022 I noticed the recessed receptacle on the left is spring loaded. I was surprised when I stuck the the adjustable screw piece with the nut I was able to press in. But then I have no piece to use on the motor side. Sent from my iPhone using Tapatalk Quote Link to comment Share on other sites More sharing options...
David Chang Posted June 30, 2022 Report Share Posted June 30, 2022 yes, right the inside hole is spring loaded..ask dennis for help. Quote Link to comment Share on other sites More sharing options...
remi Posted June 30, 2022 Report Share Posted June 30, 2022 Looks like you are all good- round cylinder/ nut in the spring loaded end; allowing you to slot the other end on the motor side Quote Link to comment Share on other sites More sharing options...
C6Bill Posted June 30, 2022 Report Share Posted June 30, 2022 No, you are not missing a part. Take the point off and adjust the length using the nut so that when you push that end into the spring loaded end it just clears the other side. Once inserted give it a little spin, there is a sleeve in the other end that accepts the fixed end. The shaft from the rotisserie motor will also fit into that sleeve and will spin the shaft. Quote Link to comment Share on other sites More sharing options...
CaptMorg82 Posted June 30, 2022 Author Report Share Posted June 30, 2022 On 6/30/2022 at 2:54 AM, David Chang said: yes, right the inside hole is spring loaded..ask dennis for help.I did give him a call but he had a message that he’s traveling through Europe but will be checking messages periodically. Sent from my iPhone using Tapatalk Quote Link to comment Share on other sites More sharing options...
CaptMorg82 Posted June 30, 2022 Author Report Share Posted June 30, 2022 On 6/30/2022 at 10:56 AM, remi said: Looks like you are all good- round cylinder/ nut in the spring loaded end; allowing you to slot the other end on the motor sideIs the other end just supposed to be the square spit with a the screw hole for the pointed piece? Nothing attached?Sent from my iPhone using Tapatalk Quote Link to comment Share on other sites More sharing options...
tekobo Posted June 30, 2022 Report Share Posted June 30, 2022 Hi there @CaptMorg82. It is not clear from your photos whether you have the piece that connects your motor to the KK. I put together a video showing how the bits fit together. Hope this helps! Quote Link to comment Share on other sites More sharing options...
CaptMorg82 Posted June 30, 2022 Author Report Share Posted June 30, 2022 On 6/30/2022 at 4:28 PM, tekobo said: Hi there @CaptMorg82. It is not clear from your photos whether you have the piece that connects your motor to the KK. I put together a video showing how the bits fit together. Hope this helps! Expand Ah, yes that's helpful, thank you! I finally see an image of what the end should look like. I believe I might have been sent the older rotisserie model and not the "hex" model. My spit is a square without any hex on the end. Quote Link to comment Share on other sites More sharing options...
CaptMorg82 Posted June 30, 2022 Author Report Share Posted June 30, 2022 The money shot: Quote Link to comment Share on other sites More sharing options...
remi Posted July 1, 2022 Report Share Posted July 1, 2022 On 6/30/2022 at 4:59 PM, CaptMorg82 said: The money shot: Expand Yes- sorry, didn't realise your rod had two square ends- because the hex end isn't an additional part as such... Having said that, I can't tell from your first photo whether you have just screwed the cylinder/ nut fitting into the hex end by mistake? Or does yours have two square ends? Quote Link to comment Share on other sites More sharing options...
C6Bill Posted July 1, 2022 Report Share Posted July 1, 2022 Did they change the design ? Quote Link to comment Share on other sites More sharing options...
CaptMorg82 Posted July 1, 2022 Author Report Share Posted July 1, 2022 Sounds like at some point there was a change. The website has both options...the square one for older KKs. "32" Big Bad 3/8" SS Rotisserie Spit w/ Center and outside Forks (Old/Square) These are for older Komodos.. current grills are all Hex in the sockets." Quote Link to comment Share on other sites More sharing options...
CaptMorg82 Posted July 1, 2022 Author Report Share Posted July 1, 2022 On 7/1/2022 at 12:16 AM, remi said: Yes- sorry, didn't realise your rod had two square ends- because the hex end isn't an additional part as such... Having said that, I can't tell from your first photo whether you have just screwed the cylinder/ nut fitting into the hex end by mistake? Or does yours have two square ends? Expand No worries, yes it's square on both ends. Working with some of Dennis' customer service reps on getting it sorted out. Seems like another case of growing pains at the new warehouse in Las Vegas and they grabbed the wrong one. Quote Link to comment Share on other sites More sharing options...
C6Bill Posted July 1, 2022 Report Share Posted July 1, 2022 (edited) Looks like what happens in Vegas doesn’t stay in Vegas anymore 😤 Edited July 1, 2022 by C6Bill 3 Quote Link to comment Share on other sites More sharing options...
tekobo Posted July 2, 2022 Report Share Posted July 2, 2022 Aha! Glad you were able to identify the problem. Rotisserie yumminess to come when you receive your new rod. 3 Quote Link to comment Share on other sites More sharing options...
