ckreef Posted September 22, 2016 Report Share Posted September 22, 2016 I think all Dutch ovens are slightly different even within the same brand. If your lid is a fairly good fit the foil should work to form a gasket. If it's a loose fit the flour paste will give you a better seal. 2 Quote Link to comment Share on other sites More sharing options...
Aussie Ora Posted September 22, 2016 Author Report Share Posted September 22, 2016 Agree if your lid jiggle heaps than flour paste would be the go if you have little movement than foil should do the trick either way you are going to end up with a sweet smellOutback Kamado Bar and Grill Quote Link to comment Share on other sites More sharing options...
Stile88 Posted September 22, 2016 Report Share Posted September 22, 2016 Now i am just curious why do we have to seal the top i thought the object was to get smoke so if some comes out of the cover wont that be fine Quote Link to comment Share on other sites More sharing options...
Syzygies Posted September 22, 2016 Report Share Posted September 22, 2016 (edited) 1 hour ago, Stile88 said: Now i am just curious why do we have to seal the top i thought the object was to get smoke so if some comes out of the cover wont that be fine If the lid leaks too fast, or comes ajar, one gets a bonfire, way too much nasty smoke. The idea is to prevent combustion inside the pot. I came up with this design after experiments with making charcoal. A classic way to make charcoal is to start a fire underneath a sealed chamber filled with wood, with holes on the bottom. Soon the wood gases from the chamber catch fire, and the starter fire underneath isn't needed. When the gases go out, one has charcoal inside the chamber. If there was instead a leak allowing convection through the chamber, one has ash inside the chamber. The idea of the holes in the bottom is to pass the wood gases through our charcoal fire, to use them as fuel and burn them off. This is a grace note of uncertain benefit. It is possible that an unsealed lid, and no holes on the bottom, would work nearly as well. I can't suggest that now without getting pilloried, after encouraging others to destroy cast iron pots with their drills? Think of it like adding the egg to cake mix, isn't it nice being involved? I've read of various very expensive setups at high end barbecue restaurants, such as Danny Meyer's Blue Smoke. Were it me, I'd design a central chamber for heating wood as one makes charcoal, and feed the fumes to "gas" ovens throughout the kitchen. I'm surprised no one has tried this. Different gas sources require different treatment (not all propane torches can handle MAPP gas), and there could be residue buildup one doesn't get with natural gas, but this seems like an engineering problem worth solving. (I doubt one could even get permits for this in a city like New York.) I got a kick out of Austin Franklin's book proposing that I make a cooker from a 1,000 gallon propane tank using "basic metal-working skills." If I had these skills and enough space, this would be my idea for offset firebox cooking. Of course, Dennis has tried this, his new cold smoker is roughly this idea. For cold smoking, one doesn't need to burn the wood gases, just expose the meat to them. For hot smoking we have other clean fuel sources. Relying entirely on wood gases for heat might be too much smoke (in my idea above, one could blend at will with natural gas, to get the smoke flavor just right) and would require a larger chamber. Edited September 22, 2016 by Syzygies 3 Quote Link to comment Share on other sites More sharing options...
Stile88 Posted September 22, 2016 Report Share Posted September 22, 2016 Thanks Syzygies for explaining that in detail much appreciated i just may try not putting holes in when i get my pot Quote Link to comment Share on other sites More sharing options...
ckreef Posted September 22, 2016 Report Share Posted September 22, 2016 1 hour ago, Stile88 said: Thanks Syzygies for explaining that in detail much appreciated i just may try not putting holes in when i get my pot. I believe if you just set the top on without any holes the wood inside will off gas. Eventually there will be enough pressure inside to force the smoke out the top. The problem with this is the smoke is now above your fire so none of the volatiles gets burned off and you have the nasty white smoke instead of the thin blue smoke you're looking for. Forcing the smoke out the bottom sends it into the fire to burn off the volatiles before it comes in contact with your meat. I too have a homemade charcoal retort in my backyard which works on this exact same principle. Wood burned in an oxygen starved environment makes charcoal. That's why you end up with lump in the smoke pot. 1 Quote Link to comment Share on other sites More sharing options...