Jump to content
EGGARY

Rib Roast on the Rotisserie

Recommended Posts

Well, after the 1st use of the Meater, I'd have to say that it met my expectations. Was easy to set up the cook. Was fun to watch the displays (there's even a time vs temp graph display). The meat thermometer end tracked along with my Thermopen, so it's pretty accurate. Unfortunately, I forgot to hook up my Maverick along side it to see how well the "ambient temperature" probe (on the opposite end) tracked. It was reading 325F at equilibrium, and I had the dome thermometer reading 375F. Makes sense, as the meat was on the "cool side" of the basket splitter. The one thing - the ambient temperature reading is very slow. While it finally reached equilibrium, it took quite a while to do so - like 15 minutes (but, the KK wasn't heat soaked, so it might have still been coming up to temp, as well for part of that time.) That was also true of the "Time Remaining" display. It took maybe 5 minutes after starting to begin to give an actual time (probably due to the algorithm that they use to do the calculation.) On most cooks where you would use the Meater, these time delays shouldn't be an issue. And, to be on the safe side, I pulled the Meater probe out of the tri-tip before I put in on the direct (hot) side of the grill to reverse sear, as I dropped down to the lower grate for that part of the cook. 

Like I said before, the jury is still out on a final verdict until I get a few more cooks under my belt with it to see how reliable it is under different conditions, like direct heat in a rotisserie cook. I also need to use it in a very long cook (10+ hours) to see how well the Meater stays charged. Would hate to have it peter out before the end of a brisket or pork butt cook. Per the instructions, it takes about 3 hours to fully recharge, so that could be a major flaw if it doesn't last long enough. One would think the designers would have thought of that and made sure the battery they chose would do the job. We'll see.

  • Like 4
Link to comment
Share on other sites

48 minutes ago, tony b said:

Well, after the 1st use of the Meater, I'd have to say that it met my expectations. Was easy to set up the cook. Was fun to watch the displays (there's even a time vs temp graph display). The meat thermometer end tracked along with my Thermopen, so it's pretty accurate. Unfortunately, I forgot to hook up my Maverick along side it to see how well the "ambient temperature" probe (on the opposite end) tracked. It was reading 325F at equilibrium, and I had the dome thermometer reading 375F. Makes sense, as the meat was on the "cool side" of the basket splitter. The one thing - the ambient temperature reading is very slow. While it finally reached equilibrium, it took quite a while to do so - like 15 minutes (but, the KK wasn't heat soaked, so it might have still been coming up to temp, as well for part of that time.) That was also true of the "Time Remaining" display. It took maybe 5 minutes after starting to begin to give an actual time (probably due to the algorithm that they use to do the calculation.) On most cooks where you would use the Meater, these time delays shouldn't be an issue. And, to be on the safe side, I pulled the Meater probe out of the tri-tip before I put in on the direct (hot) side of the grill to reverse sear, as I dropped down to the lower grate for that part of the cook. 

Like I said before, the jury is still out on a final verdict until I get a few more cooks under my belt with it to see how reliable it is under different conditions, like direct heat in a rotisserie cook. I also need to use it in a very long cook (10+ hours) to see how well the Meater stays charged. Would hate to have it peter out before the end of a brisket or pork butt cook. Per the instructions, it takes about 3 hours to fully recharge, so that could be a major flaw if it doesn't last long enough. One would think the designers would have thought of that and made sure the battery they chose would do the job. We'll see.

This is good news.  I ordered the Meater block back in January 2016.  I know the block has been delayed but it is good to get a report from somebody here who has received the probe.  Thanks for the review, Tony.  I look forward to hearing your experiences as you get more cooks with the Meater probe.

Link to comment
Share on other sites

Did the second cook last night with the MEATER. Bacon wrapped boneless beef ribs on the OctoForks. While the MEATER did a good job on the meat, the ambient temperature (and corresponding cooking time) were all over the map. The KK dome temperature was 300F and the MEATER ambient temperature reading was coming up slowly like before. Then, all of a sudden it turned over and started going down, a lot (70F)  - HUH??? :smt017 So, I went out to check on it and everything seemed OK. My first thought was - DAMN, the thing has burned out already!!! The ambient end of the probe was sticking out of the end of one rib (inserted long ways to ensure minimum depth - the probe has a scored line and the probe needs to be inserted to at least that depth), which put it near the coals on each rotation (i.e., pointed straight down at the basket). Then, all of a sudden, the temperature reading started increasing again and finally reached near the KK thermometer. I was baffled, but let the cook go on, as the meat temperature was behaving normally and that's what really mattered. Well, when I took the Fork off at the end of the cook and brought it inside and pulled the MEATER probe out of the rib, I could see what had happened. The bacon had dripped fat onto that end of the probe and coated it. There was a black crust all over the end of the probe. I guess what happened was that initially it acted like insulation, causing the reading to drop. Then, once the bacon rendered out and the fat burned off the end of the probe, the reading started going up again. Interesting for sure! Now, I just have to figure out what the next "test cook" will be??

  • Like 2
Link to comment
Share on other sites

On 6/5/2017 at 10:49 AM, tony b said:

 

Like I said before, the jury is still out on a final verdict until I get a few more cooks under my belt with it to see how reliable it is under different conditions, like direct heat in a rotisserie cook. I also need to use it in a very long cook (10+ hours) to see how well the Meater stays charged. Would hate to have it peter out before the end of a brisket or pork butt cook. Per the instructions, it takes about 3 hours to fully recharge, so that could be a major flaw if it doesn't last long enough. One would think the designers would have thought of that and made sure the battery they chose would do the job. We'll see.

I'm sure you would but I'd be cautious on where to put the  probe on a rotisserie cook.  I'd hate to see the probe work loose and fall into the fire.   I'm probably being paranoid but better safe than sorry.    How much of the probe can go into the meat?

  • Like 1
Link to comment
Share on other sites

On this cook, it was inserted past the minimum mark - probably close to 3 inches. I had to tug pretty good on it to get it out at the end of the cook and it was a chore inserting it at the beginning, so I wasn't worried about it coming out! 

  • Like 1
Link to comment
Share on other sites

12 minutes ago, tony b said:

On this cook, it was inserted past the minimum mark - probably close to 3 inches. I had to tug pretty good on it to get it out at the end of the cook and it was a chore inserting it at the beginning, so I wasn't worried about it coming out! 

Awesome!    With regards to the battery I wonder if it's replaceable?  

Link to comment
Share on other sites

On 6/9/2017 at 6:47 PM, Keith OctoForks said:

Did you say you checked distance yet?

Not as an actual "test," but i moved my phone, which was running the app, from the kitchen counter (within 6 ft of the KK) to the living room about 15 ft from the KK, and I lost the signal. So, I had to move the phone back to where it was. It sync'ed itself right back up. Was a good spot for it anyway, as that's where the phone charger is plugged in, so I just left it there to recharge.

They say if you want more distance, you need the Block version (which isn't in production yet), or to otherwise connect it to WiFi, using an old phone (don't ask me how to do that - I maybe an Engineer, but I'm computer hardware stupid - not my field at all!)

  • Like 2
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.




×
×
  • Create New...